Hello, my friends!
It's time for another fun Bowdabra project!
This will be my final Design Team post for Bowdabra,
as I've made the tough decision to stop down.
This one was a little bit tricky for me!
I had this idea, and made my bows very easily.
The tricky part came when it was time to attach my bows and take photos.
There was a windchill of -41 C at the time,
so I hope you'll understand why my photos were taken quickly! ;o)
Here's what I did using my favorite Bowdabra Burlap Ribbon:
When we moved into this house a year ago,
The yard, front and back, was filled with statues and planters, and even a fountain.
The yard, front and back, was filled with statues and planters, and even a fountain.
We quickly cleared most of them out.
However, I did decide to keep these little gargoyles
that are mounted on either side of the front door.
Our Christmas decorations/lights are still all packed up,
but I did want to add something festive.
I think the bows are a nice start.
However, I did decide to keep these little gargoyles
that are mounted on either side of the front door.
Our Christmas decorations/lights are still all packed up,
but I did want to add something festive.
I think the bows are a nice start.
Here's how I did it:
Supplies Used:
These pieces are mounted to the house with two screws.
I began by measuring the distance between the two screws.
It measured 4 1/2", so I determined that a 6" bow would be just right.
I began by measuring the distance between the two screws.
It measured 4 1/2", so I determined that a 6" bow would be just right.
1. I cut an 18" piece of wire, folded it in half, and inserted it in my Mini Bowdabra, tucking the ends under.
2. I wanted long tails on my bow. I cut a 24" piece of ribbon, and inserted it in the tool
3. Leaving 2" on the left side, I twisted my ribbon, and inserted it in the tool.
4. Since I'm making a 6" bow, I made a 3" loop on the right side. I twisted my ribbon, inserted it into the tool, and made a matching 3" loop on the left side.
5. Next I repeated the process, forming a 2" loop on either side.
6. I cut the ribbon off the spool, leaving a tail
7. After scrunching the ribbon down with the Bowdabra Wand, I untucked the ribbon. I pulled the two ribbon ends through the loop. Holding the bow down, I pulled the wire ends tight, and removed the bow from the tool.
8. I pulled the wire tight and tied a secure knot. Then I tucked the ribbon ends in, and shaped my bow.
9. I made a fishtail cut on both ends of the ribbon tails.
10. I repeated the entire process to make a second matching bow. Here are the finished and fluffed bows. I left the wire ends long, as I want to use them in the design.
11. I went out side and used the wire to fasten the bows to my gargoyles. I wrapped the wire around the mounting screws, and then tied a secure knot. I wrapped the wires around my fingers to curl them, and left them hanging. They add a nice touch of sparkle.
12. Finally, I shaped the bow loops and tails!
There you have it!
A fun festive touch has been added to my front door!
Next, I need to make little Santa hats for the Griffin
but that's a project for a different day! :o)
A fun festive touch has been added to my front door!
Next, I need to make little Santa hats for the Griffin
but that's a project for a different day! :o)
* * * * *
Thanks so much for stopping by today!
I'll be back soon with another fun project!
* * * * *
Here are all the Bowdabra links for you:
1 comment:
You have certainly shown how to use the bowdabra Nancy, I especially love your big bows on your fabulous gargoyles. Making your entrance look wonderful.
Faith x
Post a Comment